AllCozy Mk-IVLong-ezGeneralRotary EngineEngine Mounts
All Products  ----------------------------------------------------------------------------
A complete listing of all the parts  available from CG Products
Chapter headings based on Rutan derivative canard aircraft

Misc Miscellaneous parts


ClickBond
/1306 AN-3 x 0.500"

Price: $7.50 bag of 10 pcs
Product Information: see installation cartoon Clickbonds

Chapter
8
Headrests and Seat Belts

 
STEP
/1045 Step

Location: /Cozy Mk-IV & Long-ez Parts/Chapter 08 Headrest, Seat Belts
Price: $36.67 (1 required)
Product Information: port side exterior step, 1/8" 2024-T3 aluminum, bent to conform to fuselage curvature,
Value added features: bonding area sandblasted for adhesion, entire part alodined.
 

Chapter
9
Main Gear & Landing Brake


 

 
MG-1
/1041 Plate, Main Gear Mounting  
Location:
/Cozy Mk-IV Parts/Chapter 09 Main Landing Gear & Landing Brake
Price: $6.97 (4 required)

Product Information2024-T3 aluminum, alodined 

Value added features: Part was not previously offered prefab..125" 2024-T3 with 1/4" pilot hole in center. Plate had been sandblasted on bonding surface and alodined overall
 

 

MG-2/1042 Plate, Main Gear Mounting
Location:
/Cozy Mk-IV Parts/Chapter 09 Main Landing Gear & Landing Brake
Price: $8.74 (4 required)
Product Information
: 2024-T3 aluminum, alodined 
Value added features: Part was not previously offered prefab. .250" 2024-T3 aluminum. 1/4" pilot hole in center, (4) countersunk holes in the corners, sandblasted on the bonding surface and alodined overall

 

 

MKMG-4/1021 Bushing, Main Gear Mounting
Location: /Cozy Mk-IV Parts/Chapter 09 Main Landing Gear & Landing

Price: $17.75 (4 required)

Product Information: 304 stainless steel CNC turned

Value added features: sandblasted on bonding surface


LMGAB
/1156| Bushing, Main Gear
Location:
/Long-Ez Parts/Chapter 9 Main Landing Gear and Landing Brake
Price:
$15.25 (4 required)
Product Information: 304 stainless steel


MKMGA
/1137 Spacer/Sleeve Assy, Main Gear Mtg
Location:
/Cozy Mk-IV Parts/Chapter 09 Main Landing Gear & Landing Brake
Price:
$70.00 (2 required)
Product Information: 4130 steel tube  304 stainless steel bush press fit into each end
Value added features: knurled on exterior for superior bond strength, cadmium plated.

 


LMGA
/1158 Tube/Bushing Assy, Long-ez Main Gear Mtg
Location:
/Long-ez Parts/Chapter 09 Main Landing Gear & Landing Brake
Price:
$64.31 (2 required)
Product Information: 4130 steel tube  304 stainless steel bush press fit into each end
Value added features: knurled on exterior for superior bond strength, cadmium plated.

 


CZLB-18
/1043 Landing Brake Bellhorns
Location: /Cozy Mk-IV Parts/Chapter 09 Main Landing Gear & Landing Brake
Price: $8.14 (2 required)
Product Information: 2024-T3 aluminum
Value added features:  Alodined

 

Chapter
10
Canard Assembly


NC-CLT
/1003 Lift Tab
Location:
/Cozy Mk-IV Parts/Chapter 10 Canard Assy
Price:
$8.25 (2 required) (nutplate sold seperately)
Product Information:.125" 2024-T3 aluminum. Roncz Canard for Cozy & Long-Ez. For new construction (has lower hole in place). 
Value added features: Alodined

 


CG-NC-CLT
/1053 Lift Tab-HD -not available
Location:
/Cozy Mk-IV Parts/Chapter 10 Canard Assy
Price: $12.50 (2 required) (nutplate sold seperately)
Product Information: .250" 2024-T3. Roncz Canard for Cozy & Long-Ez. New construction (has lower hole)
Value added features: Alodined.
 


CG-NC-LTNP
/1092 Lift Tab Nutplate Assy
Location:
/Cozy Mk-IV Parts/Chapter 10 Canard Assy
Price: $15.00 (2 required)
Product Information: .125" 2024-T3 laser cut nutplate. For Roncz Canard Cozy & Long-Ez
Value added features: Part was not previously offered assembled. Sandblasted for adhesion and alodined. With (3) MS21047-L4 anchor nuts riveted in place
 

Chapter
11
Elevator Assembly


NC-2
/1001 Hinge Insert
Location:
/Cozy Mk-IV Parts/Chapter 11 Elevator Assy
Price: $20.60 (Cozy 4 required, Long-Ez 5 required)
Product Information: 2024-T3 aluminum. For Roncz Canard Cozy & Long-Ez
Value added features: CNC machined, sandblasted one surface, alodined. The four "corners" have been machined at the same radius where the insert is placed in the rectangular hole machined in the torque tube. Previously the builder was required to file these corners off themselves.


NC-3
/1002 Hinge Plate Assembly
Location:
/Cozy Mk-IV Parts/Chapter 11 Elevator Assy
Price: $7.36 (6 required for Cozy, 5 for Long-Ez)
Product Information: .125" 2024-T3 aluminum, water jet cut, and a bronze bushing pressed in place. For Roncz Canard Cozy & Long-Ez
Value added feature: selectively abrasive blasted, alodined
 


NC-3a
/1255 Hinge Plate Assembly
Location:
/Long-ez Parts/Chapter 11 Elevator Assy
Price: $15.00 (2 required)
Product Information: .125" 2024-T3 aluminum, water jet cut, and a bronze bushing pressed in place. For Roncz Canard
Value added feature: selectively abrasive blasted, alodined
 


NC-6
/1012 Torque Tube End Plug
Location:
/Cozy Mk-IV Parts/Chapter 11 Elevator Assy
Price: $15.95 (2 required)
Product Information: 2024-T3 aluminum. For Roncz Canard Cozy & Long-Ez
Value added features: CNC machined, alodined, also includes set screw.


NC-7
/1013 Hinge Jig
Location:
/Cozy Mk-IV Parts/Chapter 11 Elevator Assy
Price:
$4.18 (2 required)
Product Information: 5052 aluminum, Roncz Canard for Cozy & Long-Ez
Value Added Features: CNC abrasive waterject cut

 


NC-8
/1016 Hinge Pin
Location:
/Cozy Mk-IV Parts/Chapter 11 Elevator Assy
Price: $15.30 (2 required)
Product Information: 3/16" OD x 61" long stainless steel. For Cozy & Long-Ez Roncz Canard

 


CS-10
/1018 Counterbalance, outboard
Location:
/Cozy Mk-IV Parts/Chapter 11 Elevator Assy
Price: $9.75 (2 required)
Product Information: molded lead weight. For Cozy & Long-Ez Roncz Canard
Value Added Features: Molded from pure lead for highest density

 


CS-11
/1017 Counterbalance, inboard
Location:
/Cozy Mk-IV Parts/Chapter 11 Elevator Assy
Price: $7.05 (2 required)
Product Information:  Molded lead weight. For Cozy & Long-Ez Roncz Canard
Value Added Features: Molded from pure lead for highest density.

 


NC-
5a/1100 Pitch Trim Bellcrank
Location:
/Long-ez Parts/Chapter 11 Elevator Assy
Price: $60.00 (1 required )
Product Information:4130-N steel parts laser and CNC machined, TIG welded. For Roncz Canard
Value added feature: cadmium plated
 


NC-12 Left & Right
/xxxx Torque Tube Bellhorn, L & R
Location:
/Long-ez Parts/Chapter 11 Elevator Assy
Price:
$52.00 ea (left and right required)
Product Information: 4130-N steel weldment. For Long-Ez
Value Added Features: cadmium plated.
 


MKNC-12A Left
/1010 Torque Tube Offset, Left
Location:
/Cozy Mk-IV Parts/Chapter 11 Elevator Assy
Price:
$160.00 (left and right required)
Product Information: 4130-N steel weldment. For Cozy & Long-Ez While not a "per plans" part in the Long-Ez, these parts solve the serious draft problem in the Long-Ez where the eccentric moving elevator torque tubes come through the fuselage walls. This is accomplished by shifting a portion of the mechanism to be concentric with the hinge axis.
Value Added Features: This part has traditionally been made up of six individual parts welded together, we have reduced this to four CNC machined and laser cut parts. These are then TIG welded in a precision fixture and cadmium plated.

 


 

 


MKNC-12A Right
/1011 Torque Tube Offset, Right
Location:
/Cozy Mk-IV Parts/Chapter 11 Elevator Assy
Price:
$160.00 (left and right required)
Product Information: 4130-N steel weldment. For Cozy & Long-Ez While not a "per plans" part in the Long-Ez, these parts solve the serious draft problem in the Long-Ez where the eccentric moving elevator torque tubes come through the fuselage walls. This is accomplished by shifting a portion of the mechanism to be concentric with the hinge axis.
Value Added Features: This part has traditionally been made up of six individual parts welded together, we have reduced this to four CNC machined and laser cut parts. These are then TIG welded in a precision fixture and cadmium plated.

 


NC-13
/1260  Bushing, Elevator Bellcrank
Location:
/Long-Ez Parts/Chapter 11, Elevator Assembly
Price:
$5.00 (2 required)
Product Information: 4130-N steel
Value Added Features: cadmium plated
 


NCTT-CZ
/1014 Torque Tube, Elevator
Location:
/Cozy Mk-IV Parts/Chapter 11 Elevator Assy
Price: $115.74 (2 required)
Product Information: 1.00" OD x .035" wall x 52.1" long per plans. 2024-T3 aluminum. Two hinge insert pockets milled in. For Cozy plans Roncz Canard only, see Long-Ez parts listing for Long-Ez version.
Value Added Features: Now CNC machined. Entire tube has been abrasive blasted on exterior surface in preparation for bonding into elevator cores, then alodined.
Note: that these tubes are already cut to required plans length, DO NOT CUT off additional 3"

 


NCTT-L
/1025|  Elevator Torque Tube, Left
Location:
/Long-Ez Parts/Chapter 11, Elevator Assembly
Price:
$153.80 (1 required)
Product Information: for Long-Ez Roncz canard. 2024-T3 aluminum, alodined Value Added Features: Now CNC machined. Abrasive blasted in bonding area for adhesion prior to plating

 


NCTT-R
/1026|  Elevator Torque Tube, Right
Location:
/Long-Ez Parts/Chapter 11, Elevator Assembly
Price:
$122.70 (1 required)
Product Information: for Long-Ez Roncz canard. 2024-T3 aluminum, alodined Value Added Features: Now CNC machined. Abrasive blasted in bonding area for adhesion prior to plating
Note: May also be used to build long canard for Cozy Mk-IV (2 required)

 


 


CG-TTSP
/1117 Torque Tube Spool Piece
Location:
/Cozy Mk-IV Parts/Chapter 11 Elevator Assy
Price: $26.00(1 required)
Product Information: 1.00" OD x .035" wall x 30.2" long 2024-T3 aluminum tube. For Cozy Mk-IV Roncz Canard; fits between elevator offsets. Value Added Feature: Alodined. This part was formerly
builder made.
 

Chapter
12
Canard Installation


CNL
/1023  Aluminum Bushing
Location: /Cozy Mk-IV Parts/Chapter 12 Canard Installation
Price:
$6.25 (2 required)
Product Information: This is for Roncz Canard mounting bolt through F-22 in Cozy and Long-Ez. Value Added Features: Abrasive blasted and alodined.

 


CN2
/1019  Steel Bushing
Location:
/Cozy Mk-IV Parts/Chapter 12 Canard Installation
Price:
$7.50 (2 required)
Product Information: 4130-N steel. Sockets for the incidence/locating pins on Cozy and Long-Ez Roncz Canard.
Value Added Features: Cadmium plated

 

Chapter
13
Nose & Nose Gear

CG-NG-53


CG-N
G-53/1296  Gear, VENGR manual nose retract
Location:
/Long-ez, Variease Parts/Chapter 13 Nose & Nose Gear
Price:
$250.00 (1 required)
Product Information: Bronze worm shrunk fit to aluminum hub, replaces NG-53 worm and NG-56 spacer.
Value Added Features: Click on image for larger picture.
 

CG-NWA


CG-NWA
/1213  Gerdes Nosewheel Assembly
Location:
/Cozy Mk-IV Parts/Chapter 13 Nose & Nose Gear
Price:
$120.00 (1 required)
Product Information: CG-MKNG-1's shown must be purchased separately below.
Value Added Features: Click on image for details about nosewheels.
 


CG-MKNG-1
/1138  Nose Wheel Bushing, Gerdes Nosewheel
Location:
/Cozy Mk-IV Parts/Chapter 13 Nose & Nose Gear
Price:
$16.00 (2 required)
Product Information: 2024-T3 aluminum
Value Added Features: Alodined, this part is 0.100" shorter on the internal portion of the bushing than shown in the plans, requires spacer
 


CG-MKNG-1
M/1138  Nose Wheel Bushing, Matco Nosewheel
Location:
/Cozy Mk-IV Parts/Chapter 13 Nose & Nose Gear
Price:
$16.00 (2 required)
Product Information: 2024-T3 aluminum.
Value Added Features: Alodined, these parts in conjunction with the precision internal spacer allows the use of the Matco 4" nosewheel.

 

CG-NWA


CG-MKNG-1G/
NG-1 Axel Bushing, Grove Nosewheel
Location:
/Cozy Mk-IV Parts/Chapter 13 Nose & Nose Gear
Price:
$16.00 (2 required)
Product Information: NG-1 bushing for 4" Grove nosewheel
 

CG-NWA


CG-NWB
/1216  NG-1 Axel Bushing, Gerdes Nosewheel
Location:
/Long-ez Parts/Chapter 13 Nose & Nose Gear
Price:
$16.00 (2 required)
Product Information: NG-1 bushing for Long-ez Gerdes wheel
 

CG-NWA


CG-NWB-M
/1220  NG-1 Axel Bushing, Matco Nosewheel
Location:
/Long-ez Parts/Chapter 13 Nose & Nose Gear
Price:
$16.00 (2 required)
Product Information: NG-1 bushing for Long-ez Matco wheel
 

CG-NWA


CG-NWB-G
/1220  NG-1 Axel Bushing, Grove Nosewheel
Location:
/Long-ez Parts/Chapter 13 Nose & Nose Gear
Price:
$16.00 (2 required)
Product Information: NG-1 bushing for Long-ez 4" Grove nosewheel
 


CG-
FCH/1234  Forward Compartment Hinge
Location:
/Long-EZ, Cozy III, Cozy Mk-IV Parts/Chapter 13 Nose & Nose Gear
Price:
$24.00 (2 required)
Product Information: 6061-T6 aluminum.
Value Added Features: Parts are patterned after Berkut style FCH. Parts were laser cut then tumble deburred, not alodined in case you wish to polish.

 

Chapter
14
Center Section Spar
   
Chapter
15
Firewall Assembly


MKCS-71
/1036  Rudder Cable Pulley Bracket, 90 deg
Location:
/Cozy Mk-IV Parts/Chapter 15 Firewall
Price:
$7.25 (4 required)
Product Information: Stainless steel. For Cozy  and Long-Ez with forward mounted master cylinders
Two required for each pulley, two pair required per plane.
Value Added Features: Laser cut

 


CS-72
/1140  Rudder Cable Pulley Bracket, 29 deg
Location:
/Cozy Mk-IV Parts/Chapter 15 Firewall
Price:
$12.14 (2 sets required)
Product Information: Stainless steel. For Cozy and Long-Ez with forward master cylinders
These are provided as a two piece set, two sets required.
Value Added Features: Laser cut
 

Chapter
16
Control System




 


CG-JSTT
/1129  Joystick Torque Tube Assembly
Location:
/Cozy Mk-IV Parts/Chapter 16 Control System
Price:
$48.00 ea (2 required)

Product Information: Pre-assembled CS-105, CS-106, CS112. For Cozy Mk-IV
May be used with Long-Ez when combined with better Mk-IV style CZSA forked stick assembly. Image shows control stick end of tube.

Value Added Features: precision centerless ground to fit in sealed ball bearing assembly, cadmium plated. CS-106 has been alodined, CS-105 & CS-106 are fixtured, crossdrilled undersized then the cadmium plated CS-112 is press fit through the assembly.
 


CG-LECS. LE
/1265  Custom Control System Assembly
Location:
/Long-ez Parts/Chapter 16 Control System
Price:
$699.00 (1 required)
Product Information: Complete ball bearing control system from elevator connection to firewall bellcrank. (does not include universal joint)
Contact us for details.
 


CZSA
/1024  Front Stick Assembly
Location:
/Long-ez Parts/Chapter 16 Control System
Price:
$69.00 (1 required)
Product Information: 4130-N steel, cadmium plated with 2 Oilite bronze bushings pressed in place.
 


CZSA-2
/1267  Rear Stick Assembly
Location:
/Long-ez Parts/Chapter 16 Control System
Price:
$66.20 (1 required)
Product Information: 4130-N steel, cadmium plated with 2 Oilite bronze bushings pressed in place.
 


CZSA
/1024  Stick Assembly
Location:
/Cozy Mk-IV Parts/Chapter 16 Control System
Price:
$69.00 (2 required)
Product Information: 4130-N steel, cadmium plated with 2 Oilite bronze bushings pressed in place.

 


CS-1
04
/1155  Control Stick Tube
Location:
/Long-ez Parts/Chapter 16 Control System
Price:
$5.00 (2 required)
Product Information: 6061-T6 aluminum. Fits on end of stick fork assy to mount grips.
Value Added Features: alodined
 


MKCS124,L
/1027  Control Torque Tube Bellcrank, Left
Location:
/Cozy Mk-IV Parts/Chapter 16 Control System
Price:
$49.00 (1 required)
Product Information: 4130-N steel, cadmium plated
Value Added Features: 5/8”diameter tube  precision centerless ground to fit in sealed ball bearing assembly, cadmium plated

 


MKCS124,R
/1028  Control Torque Tube Bellcrank, Right
Location:
/Cozy Mk-IV Parts/Chapter 16 Control System
Price:
$49.00 (1 required)
Product Information: 4130-N steel, cadmium plated
Value Added Features: 5/8”diameter tube has been precision centerless ground to fit in sealed ball bearing assembly, cadmium plated.
Note: can be used in Long-Ez as well

 


CG-CS-
108/117/
/1243  Control System Bearing Assembly
Location:
/Cozy Mk-IV Parts/Chapter 16 Control System
Price:
$50.00 (4 required)
Product Information: Sealed ball bearing in anodized lightweight aluminum housing. 5/8" ID. Use matching precision ground tubes CS-115 and CS-JSTT Joystick Torque Tube Assemblies with these.

Value Added Features: Includes Clickbond mounting hardware, see instructions on our web site.

Note: can be used in Long-Ez as well

 


CG-CS-
123/
/1196  Bearing Assembly, Firewall
Location:
/Long-ez Parts/Chapter 16 Control System
Price:
$54.00 (2 required)
Product Information: Sealed ball bearing in anodized lightweight aluminum housing. 5/8" ID. Use matching precision ground control torque tube bellcranks CS-124-L&R with these.
Value Added Features:
Bearing installed in housing with snap ring.
 


CG-CS-181-QDK
/1246  Pushrod Quick Disconnect Kit
Location:
/Long-ez Parts/Chapter 16 Control System
Price:
$18.35 (4 required)
Product Information: 2024-T3 aluminum
Value Added Features: clevis pin, safety clip, washer and rivets included.
 


CS-1A
/1052  Pushrod Threaded Insert, Aluminum
Location:
/Cozy Mk-IV Parts/Chapter 16 Control System
Price:
$8.00 (4 required)
Product Information: 2024 Aluminum, AN-4 thread, Alodine plated
Value Added Features:
Length has been increased slightly to allow rod ends to be screwed in deeper if necessary.
Note:
can be used in Long-Ez as well
 


CS-50
/1029  Pushrod Threaded Insert, Steel
Location:
/Cozy Mk-IV Parts/Chapter 16 Control System
Price:
$8.31 (10 required)
Product Information: Steel. 4130-N steel, AN-4 thread, cadmium plated Value Added Features: Length has been increased slightly to allow rod ends to be screwed in deeper if necessary.
Note:
can be used in Long-Ez as well
 


CS-17
/1032  Rudder Pedal Thimble Spacer
Location:
/Cozy Mk-IV Parts/Chapter 16 Control System
Price:
$5.00 (2 required)
Product Information: 2024-T3 aluminum, alodined
Note: can be used in Long-Ez as well

 


CS-115
/1107  Tube, Rear Seat Bearing
Location:
/Cozy Mk-IV Parts/Chapter 16 Control System
Price:
$5.00 (2 required)
Product Information: 4130-N steel
Value Added Features: 5/8”diameter tube has been precision centerless ground to fit in sealed ball bearing assembly, cadmium plated
Note: can be used in Long-Ez as well

 


CS-202
/1261  Spacer, Elevator Bellcrank
Location:
Long-ez Parts/Chapter 16 Control System
Price:
$5.00 (2 required)
Product Information: 2024-T3 aluminum
 


CS-201
/1035  Bushing
Location:
/Cozy Mk-IV Parts/Chapter 16 Control System
Price:
$5.00 (8 required)
Product Information: 4130-N steel, cadmium plated. Used to space spherical rod ends away from control sticks etc
Note: can be used in Long-Ez as well

 

Chapter
17
Trim & Landing Brake


RT-2L
/1046  Roll Trim Bracket, Left
Location:
/Cozy Mk-IV Parts/Chapter 17 Trim and Landing Brake
Price:
$4.50 (1 required)
Product Information: 4130-N steel, cadmium plated


RT-2R
/1047  Roll Trim Bracket, Right
Location:
/Cozy Mk-IV Parts/Chapter 17 Trim and Landing Brake
Price:
$4.50 (1 required)
Product Information: 4130-N steel, cadmium plated


CZRTH
/1048  Roll Trim Handle
Location:
/Cozy Mk-IV Parts/Chapter 17 Trim and Landing Brake
Price:
$30.30 (1 required)
Product Information: 2024-T3 aluminum
Value Added Features: Water jet cut and tumble deburred for a pleasing “feel”, may be polished.

 


CZPTH
/1049|  Pitch Trim Handle
Location:
/Cozy Mk-IV Parts/Chapter 17 Trim and Landing Brake
Price:
$38.85(1 required)
Product Information: 2024-T3 aluminum
Value Added Features: Water jet cut and tumble deburred for a pleasing “feel”, may be polished.

 


CZLB-1
/1050|  Spacer
Location:
/Cozy Mk-IV Parts/Chapter 17 Trim and Landing Brake
Price:
$5.00 (2 required)
Product Information: 2024-T3 aluminum, alodined

 




Picture not available


CZLB-6
/1071|  Spacer
Location:
/Cozy Mk-IV Parts/Chapter 17 Trim and Landing Brake
Price:
$4.37 (2 required)
P
roduct Information: 4130-N steel, cadmium plated

 

Chapter
18
Canopy
Chapter
19
Wings


CS-127
/1076|  Bracket, Aileron Bellcrank Linkage
Location:
/Cozy Mk-IV Parts/Chapter 19 Wings
Price:
$7.60 (4 required)
Product Information: 304 stainless steel
Value Added Features: holes for end stops added. Additional hole added for pinning aileron linkage while centering control surfaces and sticks.

 


CS-128/1141|  Bellcrank Aileron Linkage
Location:
/Cozy Mk-IV Parts/Chapter 19 Wings
Price:
$53.00 (2 required)
Product Information: 2024-T3 aluminum, alodined, has ball bearing assembly riveted in place
Value Added Features: Additional hole added for pinning aileron linkage while centering control surfaces and sticks.
 


CS-131
/1078|  Spacer, Aileron Bellcrank Linkage
Location:
/Cozy Mk-IV Parts/Chapter 19 Wings
Price:
$5.38 (2 required)
Product Information: 4130-N steel, cadmium plated


CS-132
/1079|  Bellcrank, Aileron Tube
Location:
/Cozy Mk-IV Parts/Chapter 19 Wings
Price:
$50.00 (2 required)
Product Information: 4130-N steel, cadmium plated
Value Added Features: the major radius on this part is per plans, unlike the large radius on the former Brock part (done for easier welding) that could cause clearance issues
Note: this is a required upgrade to all Long-Eze’s

 


CS-152
/1101|  Tube, Aileron Bellcrank Bearing,
Location:
/Cozy Mk-IV Parts/Chapter 19 Wings
Price:
$5.00 (2 required)
Product Information: 4130-N steel, cadmium plated
Value Added Features: 5/8”diameter tube has been precision centerless ground to fit in sperical ball bearing assembly, cadmium plated
Note: can be used in Long-Ez as well

 


A2
/1083|  Bracket, Inboard Aileron Hinge Mount
Location:
/Cozy Mk-IV Parts/Chapter 19 Wings
Price:
$12.95 (2 required)
Product Information: 2024-T3 aluminum, alodined
Value Added Features: part has been abrasive blasted in bonding area and alodined
Note: can be used in Long-Ez as well

 


A5
/1084|  Bracket, Outboard Aileron Hinge Mount
Location:
/Cozy Mk-IV Parts/Chapter 19 Wings
Price:
$9.62 (4 required)
Product Information: 2024-T3 aluminum, alodined
Value Added Features: part has been abrasive blasted in bonding area and alodined
Note: can be used in Long-Ez as well

 


A10
/1244  Tube, Aileron
Location:
/Long-ez Parts/Chapter 19 Wings
Price:
$12.00 (2 required)
Product Information: 60-61-T6 aluminum, alodined
Value Added Features: part has been abrasive blasted in bonding area and alodined
 


CG-
PI
/1295  Insert, baggage pod mounting
Location:
/General Parts/Chapter 19 Wings
Price:
$6.57 (12 required)
Product Information: 2024-T3 aluminum 1" long x 3/8" dia, AN-3 thread thru.
Value Added Features: part has been knurled in bonding area
Note: can be used in any place you need internal threads for mounting parts
can be cut shorter or partially buried in foam to give a standoff, many uses.


LWA-9
/1085|  Bushing, Wing Bolt
Location:
/Cozy Mk-IV Parts/Chapter 19 Wings
Price:
$10.00 (12 required)
Product Information: 2024-T3 aluminum, alodined
Value Added Features: part has been abrasive blasted in bonding area.
Note: can be used in Long-Ez as well

Chapter
20
Winglets & Rudders


C
G-RRT
/1118  Rudder Return Spring Tube
Location:
/Long-ez Parts/Chapter 20 Winglets and Rudders
Price:
$6.50 (2 required)
Product Information: 2024-T3 aluminum tube
Value Added Features: abrasive blasted for bonding, alodined
 


CS-301L
/1087|  Rudder Horn, Left
Location:
/Cozy Mk-IV Parts/Chapter 20 Wingletss and Rudders
Price:
$11.00 (1 required)
Product Information: 304 stainless steel
Value Added Features: laser cut
Note: can be used in Long-Ez as well

 


CS-301R
/1088|  Rudder Horn, Right
Location:
/Cozy Mk-IV Parts/Chapter 20 Wingletss and Rudders
Price:
$11.00 (1 required)
Product Information: 304 stainless steel
Value Added Features: laser cut
Note: can be used in Long-Ez as well

 


CG-HRH
/1089|  Hidden Rudder Horn
Location:
/Long-ez Alternative Parts/Chapter 20 Winglets and Rudders
Price:
$30.00 ea. (2 required)
Product Information
: 2024-T3 aluminum, alodined, 4130-N steel, cadmium plated, assembled with rivits.
Value Added Features: Laser cut parts. Selectively abrasive blasted in bonding area for adhesion prior to plating.  Assembly includes clevis pin and cotter pin.
 

Chapter
23
Engine Installation


EM-30/
1154  Cozy Mk-IV Dynafocal Type 1 Engine Mount
Location:
/Cozy Mk-IV Parts/Chapter 23 Engine Installation
Price: $1350.00 (1 required)
Product Information: 4130-N steel tubing. This mount is for per-plans Lycoming installation of 0-320 & 0-360 engines with 30 degree mounting lugs (typical). Uses Lord J-7402-24 (in stock at Aircraft Spruce #07-01115) vibration isolators.
Call for availability



EM-30io HD/
1235 
Cozy Mk-IV HD Dynafocal Type 1 Engine Mount
Location:
/Cozy Mk-IV Parts/Chapter 23 Engine Installation
Price: $1350.00 (1 required)
Product Information: A Heavy Duty version using the next wall size up 4130-N steel tubing. with additional gusseting. This mount is for Lycoming fuel injected engine installation of IO-320 & IO-360 engines with 30 degree mounting lugs (typical)
Known as an H-Brace mount due to configuration of lower brace to clear induction system.
Uses Lord J-7402-24 (in stock at Aircraft Spruce #07-01115) vibration isolators.
Call for availability


EM-18
/  Cozy Mk-IV Dynafocal Type 2 Engine Mount
Location:
/Cozy Mk-IV Parts/Chapter 23 Engine Installation
Price: $1350.00 (1 required)
Product Information: 4130-N steel tubing. This mount is for per-plans Lycoming installation of 0-320 & 0-360 engines with 18 degree mounting lugs (rare). Uses Lord J-7402-24 (in stock at Aircraft Spruce #07-01115) vibration isolators.
Call for availability


EM-18io 
Cozy Mk-IV Dynafocal Type 2 Engine Mount
Location:
/Cozy Mk-IV Parts/Chapter 23 Engine Installation
Price: $1350.00 (1 required)
Product Information: 4130-N steel tubing. This mount is for per-plans Lycoming installation of I0-320 & I0-360 engines with 18 Known as an H-Brace mount due to configuration of lower brace to clear induction system. Uses Lord J-7402-24 (in stock at Aircraft Spruce #07-01115) vibration isolators.
Call for availability
 


EM-C/
1108
Cozy Mk-IV Conical Type Engine Mount
Location:
/Cozy Mk-IV Parts/Chapter 23 Engine Installation
Price: $1150.00 (1 required)
Product Information: 4130-N steel tubing. This mount is for per Lycoming installation of 0-320 & 0-360 engines with conical mounting lugs (rare).
Call for availability
 


EM-540
/1268  Cozy Mk-IV Lycoming 0-540 Engine Mount
Location:
/Cozy Mk-IV Parts/Chapter 23 Engine Installation
Price: $1350.00 (1 required)
Product Information: 4130-N steel tubing. This mount is for installation of  Lycoming  0-540 6 cylinder engines. Airframe requires substantial reinforcement for the higher horsepower and stress. Additional firewall mounting point is centered 10" above top two plans mounting points.
Call for availability
 

Click For A Larger Image


EM-LE-1/
1230  Long-EZ Heavy Duty Dynafocal Type 1 Engine Mount
Location:
/Long-EZ Parts/Chapter 23 Engine Installation
Price: $1050.00 (1 required)
Product Information: 4130-N steel tubing. This mount is for per-plans Lycoming installation of 0-320 & 0-360 engines with 30 degree mounting lugs (typical). Uses Lord J-7402-24 (in stock at Aircraft Spruce #07-01115) vibration isolators.
Value Added Features: Click image for larger picture; has two additional upper tubes.
Call for availability

Click For A Larger Image


EM-LE-2/ 
Long-EZ Heavy Duty Dynafocal Type 2 Engine Mount
Location:
/Long-EZ Parts/Chapter 23 Engine Installation
Price: $1050.00 (1 required)
Product Information: 4130-N steel tubing. This mount is for per-plans Lycoming installation of 0-290 & 0-320 engines with 18 degree mounting lugs. Uses Lord J-7402-24 (in stock at Aircraft Spruce #07-01115) vibration isolators.
Value Added Features: Click image for larger picture; has two additional upper tubes.
Call for availability

Click For A Larger Image


EM-LE-C/
1114 
Long-EZ Heavy Duty Conical Engine Mount
Location:
/Long-EZ Parts/Chapter 23 Engine Installation
Price: $900.00 (1 required)
Product Information: 4130-N steel tubing. This mount is for per-plans Lycoming installation of 0-290 & 0-320 engines with conical mounting lugs (typical of 0-290)
Click image for larger picture

Call for availability

Click For A Larger Image


EM-MKRX-13B 
Cozy Mk-IV 13B/Renesis Rotary Engine Mount
Location:
/Cozy Mk-IV Parts/Chapter 23 Engine Installation
Price: $1150.00 (1 required)
Product Information: 4130-N steel tubing. This mount is for mounting a two rotor engine. Requires matching engine bed mounting plate.
 

Call for availability

Parts Common to 13B/Renesis & 20B Engines

 


CG-RX-LMK Lord Mount Kit,
Rotary Engine Mount vibration isolators
Price: $80.08 (4 sets)
Product Information: Includes rubber vibration isolators and hardware for our rotary engine mounts.
 

Click For A Larger Image


CG-RX-RMP Reduction Drive Mounting Plate / Side Starter

Price: (only available with complete mounting kit at this time)
Product Information: Side mount starter type redrive mounting plate for RWS Redrive.
Includes standoffs, spacers and hardware.  Requires Lord Mount Kit, 13B or 20B Bolt Kit and Tubular Mount.
 

Click For A Larger Image


CG-RX-RMP standoff kit (only available with above CG-RX-RMP)

Price: (only available with complete mounting kit at this time)
Product Information: Side mount starter type redrive mounting plate standoff kit for RWS Redrive.Includes standoffs, spacers and hardware.  Requires Lord Mount Kit, 13B or 20B Bolt Kit and Tubular Mount.
 

13B 13B & Renesis Engines

 


CG-RX-BMSS-13B  Bed Mount Plate & Reduction Drive Mounting Plate kit

Price: $1016.50
Product Information: Includes side mount starter type redrive mounting plate, standoffs, spacers and bed mounting plate. Requires Lord Mount Kit, 13B Bolt Kit and Tubular Mount.
 

Click For A Larger Image


EM-MKRX-13B 
Cozy Mk-IV 13B/Renesis Tubular Engine Mount
Location:
/Cozy Mk-IV Parts/Chapter 23 Engine Installation
Price: $1150.00
Product Information: 4130-N steel tubing. This mount is for mounting a two rotor engine. Requires matching engine bed mounting plate. Fits CCI bed plates.
 

 


EM-LERX-13B  Long-EZ
13B/Renesis Tubular Engine Mount
 (coming soon).
Location:
/Long-EZ Parts/Chapter 23 Engine Installation
Price: $1150.00
Product Information: 4130-N steel tubing. This mount is for mounting a two rotor engine. Requires matching engine bed mounting plate. Fits CCI bed plates.
 


CG-RX-RING-13B  Ring, Bed Plate
13B/Renesis Rotary Engine Mount
Price: $320.00
Product Information: 4130-N steel tubing. This ring is the bed mounting plate support portion of our engine mounts for welding your own custom mount for a two rotor engine. Requires matching engine bed mounting plate. Fits CCI bed plates.
 

Click For A Larger Image


CG-RX-MMP-13B  Bed Mounting Plate,
13B/Renesis Rotary Engine Mount
Price: $464.64
Product Information: 6061-T6 Aluminum. Bed Mounting Plate. Extended portion at flywheel end mates to our reduction drive mounting plate for added rigidity.
Applicable with any airframe, fits CCI tubular mounts.
 

20B 20B Engines

 


CG-RX-BMSS-20B  Bed Mount Plate & Reduction Drive Mounting Plate kit

Price: $1109.34
Product Information: Includes side mount starter type redrive mounting plate, standoffs, spacers and bed mounting plate. Requires Lord Mount Kit, 20B Bolt Kit and Tubular Mount.
 

Click For A Larger Image


EM-MKRX-20B 
Cozy Mk-IV 20B Rotary Engine Mount
Location:
/Cozy Mk-IV Parts/Chapter 23 Engine Installation
Price: $1150.00
Product Information: 4130-N steel tubing. This mount is for mounting a three rotor engine. Requires matching engine bed mounting plate .
 

 


EM-LERX-20B  Long-EZ
20B Rotary Engine Mount
 (coming soon).
Location:
/Long-EZ Parts/Chapter 23 Engine Installation
Price: $1150.00
Product Information: 4130-N steel tubing. This mount is for mounting a three rotor engine. Requires matching engine bed mounting plate.
 


CG-RX-RING-20B  Ring, Bed Plate
20B Rotary Engine Mount
Price: $320.00
Product Information: 4130-N steel tubing. This ring is the bed mounting plate support portion of our engine mounts for welding your own custom mount for a three rotor engine. Requires matching engine bed mounting plate.
 

Click For A Larger Image


CG-RX-MMP-20B  Bed Mounting Plate,
20B Rotary Engine Mount
Price: $557.48
Product Information: 6061-T6 Aluminum. Bed Mounting Plate. Extended portion at flywheel end mates to our reduction drive mounting plate for added rigidity.